|
技术交流 | 电路欣赏 | 工控天地 | 数字广电 | 通信技术 | 电源技术 | 测控之家 | EMC技术 | ARM技术 | EDA技术 | PCB技术 | 嵌入式系统 驱动编程 | 集成电路 | 器件替换 | 模拟技术 | 新手园地 | 单 片 机 | DSP技术 | MCU技术 | IC 设计 | IC 产业 | CAN-bus/DeviceNe |
用过m25p16存储器的请教 |
作者:nxzp12348 栏目:技术交流 |
M25P16的操作,有一个9v的电压,是不是必不可少? 看了半天没有明白。 我现在只是简单的数据存储和读取,不要那么复杂。 用过的能帮忙说一下它的使用情况吗 谢谢 |
2楼: | >>参与讨论 |
作者: 李冬发 于 2006/12/14 21:34:00 发布:
哪来的9V?只有一个3.3V的电源吧 |
3楼: | >>参与讨论 |
作者: nxzp12348 于 2006/12/15 8:41:00 发布:
VP,编程时候要求9v |
4楼: | >>参与讨论 |
作者: 李冬发 于 2006/12/15 12:20:00 发布:
老兄,你是看谁家的手册啊,我的手册上怎么没找到9V的字样 我用的M25P80-VMF6P也不需要9V电源啊 |
5楼: | >>参与讨论 |
作者: nxzp12348 于 2006/12/15 14:01:00 发布:
冬发兄,多多发财 Write Protect/Enhanced Program supply voltage (W/VPP) W/VPP is both a CONTROL input and a POWER supply pin. The two functions are selected by the voltage range applied to the pin. If the W/VPP input is kept in a low voltage range (0V to VCC) the pin is seen as a CONTROL input. This input signal is used to freeze the size of the area of MEMORY that is protected against program or erase instructions (as specified by the values in the BP2, BP1 and BP0 bits of the Status Register). If VPP is in the range of VPPH it acts as an additional POWER supply pin. In this case VPP must be stable until the Program/Erase algorithm is completed. VPP=9v 这个时M25P32的手册。 能说说你是怎么做的吗? 操作的时候对这个没有操作吗》? |
6楼: | >>参与讨论 |
作者: 李冬发 于 2006/12/15 14:58:00 发布:
呵呵,我的手册上没有这些(M25P32.pdf) Write Protect (W). The main purpose of this input signal is to freeze the size of the area of MEMORY that is protected against program or erase instructions (as specified by the values in the BP2, BP1 and BP0 bits of the Status Register). |
7楼: | >>参与讨论 |
作者: 李冬发 于 2006/12/15 15:01:00 发布:
http://cn.ic-on-line.cn/IOL/datasheet/M25P32_457052.pdf |
8楼: | >>参与讨论 |
作者: nxzp12348 于 2006/12/15 21:27:00 发布:
可恶,资料不一样 http://www.icbase.com/default.asp http://www.icbase.com/pdf/STM/STM30160610.pdf 我在武汉力源查的资料。 想电路上怎么实现这个9v电压,纳闷了好几天。 他们资料M25P16资料上面没有vpp,但是M25P32上面有这个东西。 害人不浅那! 谢谢老兄! 你用过吗?能不能留个联系方式,有问题请教你?我在上海。 |
9楼: | >>参与讨论 |
作者: 李冬发 于 2006/12/15 21:44:00 发布:
签名里有 |
10楼: | >>参与讨论 |
作者: nxzp12348 于 2007/1/5 17:37:00 发布:
请教M25P**的操作 发兄你好: 有个问题想请教一下:因为数据量比较大,我现在用M25P32做数据存储器,好像没有更好的选择。 但这种器件在页编程的时候,是不是只能总每一页的起始地址存储数据?不能从任意地址开始吗? 我的每次存储数据在10个字节左右,这样不是要浪费很多地址吗? 不知道的理解对不对,请多多指教! The Page Program (PP) instruction is entered by driving Chip SELECT (S) Low, followed by the instruction code, three address bytes and at least one data byte on Serial Data Input (D). If the 8 least significant address bits (A7-A0) are not all zero, all transmitted data that goes beyond the end of the current page are programmed from the start address of the same page (from the address whose 8 least significant bits (A7-A0) are all zero). Chip SELECT (S) must be driven Low for the entire duration of the sequence. |
|
|
免费注册为维库电子开发网会员,参与电子工程师社区讨论,点此进入 |
Copyright © 1998-2006 www.dzsc.com 浙ICP证030469号 |