Solid State Sensors
Hall Effect Vane Position Sensors
FEATURES
Operated by vane interrupter
鈥?0 to
+125掳C
temperature range
Current sinking output
Smaller size than 2AV
Four pin in-line printed circuit board
terminals or leadwires
Closely controlled differential to
predict pulse width
4.5 to 5.5 or 6 to 16 VDC power
supply
4AV ORDER GUIDE
Catalog Listings
Supply Voltage (VDC)
Supply Current (mA max.)
Output Type
Output Voltage (V)
Current per Output (mA)
Termination
4AV11C
4.5 to 5.5
7.0
Sink
0.4
4
PC Board
4AV12C
4.5 to 5.5
7.0
Sink
0.4
8
Leadwire
4AV11A
6 to 16
13.0
Sink
0.4
10
PC Board
4AV12A
6 to 16
13.0
Sink
0.4
20
Leadwire
4AV Series
GENERAL INFORMATION
AV vane operated integral magnet posi-
tion sensors are operated by passing a
ferrous vane through the gap between the
Hall sensor and the magnet, shunting the
magnetic flux away from the sensor. AVs
can be used as limit switches by oper-
ating with a single large vane; as tachom-
eter sensors by using toothed wheels; or
as synchronizing elements by using
cams or sectors. AV Series have many
features in common such as:
Operation by a low cost, easy to
fabricate ferrous vane
Magnet and sensor incorporated in
same rugged package
Sealed construction . . . unaffected by
dust or dirt
0 to 100 kHz operating speed . . . no
minimum speed of operation
On and Off times programmable by
vane dimensioning
Precision mechanical operating
characteristics
L-R
Diff.
2,5/.100
PDFINFO
p a g e - 0 5 1
AV MECHANICAL CHARACTERISTICS
Series
4AV*
Left
Operate
a
5,4/.213
Mag.
Release
b
6,0/.237
Slope
Diff.
0,6/.024
Right
Operate
d
8,6/.337
Release
c
7,9/.313
Diff.
0,6/.024
VANE OPERATION
* Operating characteristics of the 4AV are adjusted to produce a .100卤.010 dimension between the operate
point on one side of the switch, to the release point on the other side. The actuator can be designed to produce a
specific pulse width for timing or sequencing operations.
Integral Magnet
VANE DIMENSIONS (mm/in.)
Thickness
1,0/.04
1,6/.06
Min. Window
10,2/.40
10,2/.40
Min. Tooth
10,2/.40
6,3/.25
Min. Tooth
Depth
9,3/.37
Vane material:
Cold rolled steel, 1018 or low in carbon (annealed).
MOUNTING DIMENSIONS
(For reference only)
1. With no vane in the gap the output is
conducting (Sinking is Low, Sourcing
is High).
2. Vane movement from left to right.
When leading edge reaches 鈥樷€榖鈥欌€? the
output stops conducting (Sinking
goes High, Sourcing goes Low).
3.
After leading edge reaches 鈥樷€榖鈥欌€?
A. If the vane moves on through the
gap; when the trailing edge
reaches 鈥樷€榙鈥欌€? the output will be
conducting.
B. If direction of vane travel
reverses;
鈥樷€榓鈥欌€? output will be
conducting.
4. For vane movement from right to left,
output is non-conducting when the
leading edge reaches 鈥樷€榗鈥欌€? and is
conducting when the trailing edge
reaches 鈥樷€榓鈥欌€?
BLOCK DIAGRAM
Leadwire
PC Board
Honeywell MICRO SWITCH Sensing and Control 1-800-537-6945 USA
1-815-235-6847 International 1-800-737-3360 Canada
51
1
