您的位置：维库电子市场网 > Datasheet > P87C552
P87C552数据手册封面

P87C552 Datasheet

  • P87C552

  • 80C51 8-bit microcontroller

  • 393.52KB

  • Philips

阅览下载 纠错 0

扫码查看芯片数据手册

上传产品规格书

PDF预览

Philips Semiconductors
Preliminary specification
80C51 8-bit microcontroller
8K/256 OTP, 8 channel 10 bit A/D, I
2
C, PWM,
capture/compare, high I/O, low voltage (2.7V鈥?.5V), low power
P87C552
Interrupts
The 8XC552 has fifteen interrupt sources, each of which can be
assigned one of four priority levels. The five interrupt sources
common to the 80C51 are the external interrupts (INT0 and INT1),
the timer 0 and timer 1 interrupts (IT0 and IT1), and the serial I/O
interrupt (RI or TI). In the 8XC552, the standard serial interrupt is
called SIO0.
The eight Timer T2 interrupts are generated by flags CTI0-CT13,
CMI0-CMI2, and by the logical OR of flags T2OV and T2BO. Flags
CTI0 to CT13 are set by input signals CT0I to CT3i. Flags CMI0 to
CMI2 are set when a match occurs between Timer T2 and the
compare registers CM0, CM1, and CM2. When an 8-bit or 16-bit
overflow occurs, flags T2BO and T2OV are set, respectively. These
nine flags are not cleared by hardware and must be reset by
software to avoid recurring interrupts.
The ADC interrupt is generated by the ADCI flag in the ADC control
register (ADCON). This flag is set when an ADC conversion result is
ready to be read. ADCI is not cleared by hardware and must be
reset by software to avoid recurring interrupts.
The SIO1 (I
2
C) interrupt is generated by the SI flag in the SIO1
control register (S1CON). This flag is set when S1STA is loaded
with a valid status code.
The ADCI flag may be reset by software. It cannot be set by
software. All other flags that generate interrupts may be set or
cleared by software, and the effect is the same as setting or
resetting the flags by hardware. Thus, interrupts may be generated
by software and pending interrupts can be canceled by software.
Interrupt Enable Registers:
Each interrupt source can be
individually enabled or disabled by setting or clearing a bit in the
interrupt enable special function registers IEN0 and IEN1. All
interrupt sources can also be globally enabled or disabled by setting
or clearing bit EA in IEN0. The interrupt enable registers are
described in Figures 26 and 27.
There are 3 SFRs associated with each of the four-level interrupts.
They are the IENx, IPx, and IPxH. (See Figures 28, 29, and 30.) The
IPxH (Interrupt Priority High) register makes the four-level interrupt
structure possible.
The function of the IPxH SFR is simple and when combined with the
IPx SFR determines the priority of each interrupt. The priority of
each interrupt is determined as shown in the following table:
PRIORITY BITS
IPxH.x
0
0
1
1
IPx.x
0
1
0
1
INTERRUPT PRIORITY LEVEL
Level 0 (lowest priority)
Level 1
Level 2
Level 3 (highest priority)
The priority scheme for servicing the interrupts is the same as that
for the 80C51, except there are four interrupt levels rather than two
as on the 80C51. An interrupt will be serviced as long as an interrupt
of equal or higher priority is not already being serviced. If an
interrupt of equal or higher level priority is being serviced, the new
interrupt will wait until it is finished before being serviced. If a lower
priority level interrupt is being serviced, it will be stopped and the
new interrupt serviced. When the new interrupt is finished, the lower
priority level interrupt that was stopped will be completed.
7
IEN0 (A8H)
EA
(MSB)
BIT
IEN0.7
6
EAD
5
ES1
4
ES0
3
ET1
2
EX1
1
ET0
0
EX0
(LSB)
SYMBOL
EA
FUNCTION
Global enable/disable control
0 = No interrupt is enabled
1 = Any individually enabled interrupt will be accepted
Eanble ADC interrupt
Enable SIO1 (I
2
C) interrupt
Enable SIO0 (UART) interrupt
Enable Timer 1 interrupt
Enable External interrupt 1
Enable Timer 0 interrupt
Enable External interrupt 0
IEN0.6
IEN0.5
IEN0.4
IEN0.3
IEN0.2
IEN0.1
IEN0.0
EAD
ES1
ES0
ET1
EX1
ET0
EX0
SU00762
Figure 26. Interrupt Enable Register (IEN0)
1999 Mar 30
28

P87C552相关型号PDF文件下载

您可能感兴趣的PDF文件资料

热门IC型号推荐

©2024 维库电子市场网（www.dzsc.com）　备案号：浙B2-20050339-1 经营许可证：浙B2-20210386版权声明
买家服务热线：0571-85317607 | 买家服务部QQ： QQ:1609526468
卖家服务热线：0571-85317607 | 卖家服务部QQ： QQ:331652727

扫码下载APP，
一键连接广大的电子世界。

在线人工客服

买家服务：
卖家服务：

0571-85317607

客服在线时间周一至周五
9:00-17:30

关注官方微信号，
第一时间获取资讯。

建议反馈
返回顶部

建议反馈

联系人：

联系方式：

按住滑块，拖拽到最右边
>>
感谢您向阿库提出的宝贵意见，您的参与是维库提升服务的动力！意见一经采纳，将有感恩红包奉上哦！

PDF纠错X

投诉电话：0571-85317607 投诉QQ：

如选匿名将无法为您反馈投诉结果，建议实名投诉！