您的位置：维库电子市场网 > Datasheet > EN29LV640

EN29LV640 Datasheet

  • EN29LV640

  • Eon Silicon Solution Inc. [64 Megabit (4M x 16-bit ) CMOS 3...

  • 423.46KB

  • EON

阅览下载 纠错 0

扫码查看芯片数据手册

上传产品规格书

PDF预览

EN29LV640
Any commands written to the device during the program operation are ignored. Programming status
can be checked by sampling data on DQ7 (DATA# polling) or on DQ6 (toggle bit). When the
program operation is successfully completed, the device returns to read mode and the user can read
the data programmed to the device at that address. Note that
data can not be programmed from a
鈥?鈥?to a 鈥?鈥?
Attempting to do so may halt the operation and set DQ5 to 鈥?鈥? or cause the Data#
Polling algorithm to indicate the operation was successful. However, a succeeding read will show
that the data is still 鈥?鈥? Only erase operations can convert a 鈥?鈥?to a 鈥?鈥? When programming time
limit is exceeded, DQ5 will produce a logical 鈥?鈥?and a Reset command can return the device to
Read mode.
Programming is allowed in any sequence across sector boundaries.
Unlock Bypass
To speed up programming operation, the Unlock Bypass Command may be used. Once this feature
is activated, the shorter two-cycle Unlock Bypass Program command can be used instead of the
normal four-cycle Program Command to program the device. During the unlock bypass mode, only
the Unlock Bypass Program and Unlock Bypass Reset command can be accepted. This mode is
exited after issuing the Unlock Bypass Reset Command. The device powers up with this feature
disabled
The device provides accelerated program operations through the WP#
/
ACC pin. When WP#
/
ACC is
asserted to V
HH
, the device automatically enters the Unlock Bypass mode. The system may then
write the two-cycle Unlock Bypass Program command sequence.
B
B
Chip Erase Command
Chip erase is a six-bus-cycle operation. The chip erase command sequence is initiated by writing
two unlock cycles, followed by a set-up command. Two additional unlock write cycles are then
followed by the chip erase command, which in turn invokes the Embedded Erase algorithm. The
device does not require the system to preprogram prior to erase. The Embedded Erase algorithm
automatically preprograms and verifies the entire memory for an all zero data pattern prior to
electrical erase. The system is not required to provide any controls or timings during these
operations. The Command Definitions table shows the address and data requirements for the chip
erase command sequence.
Any commands written to the chip during the Embedded Chip Erase algorithm are ignored.
The system can determine the status of the erase operation by using DQ7, DQ6, or DQ2. See 鈥淲rite
Operation Status鈥?for information on these status bits. When the Embedded Erase algorithm is
complete, the device returns to reading array data and addresses are no longer latched.
Sector Erase Command Sequence
Sector erase is a six bus cycle operation. The sector erase command sequence is initiated by
writing two un-lock cycles, followed by a set-up command. Two additional unlock write cycles are
then followed by the address of the sector to be erased, and the sector erase command. The
Command Definitions table shows the address and data requirements for the sector erase
command sequence.
Once the sector erase operation has begun, only the Erase Suspend command is valid. All other
commands are ignored. If there are several sectors to be erased, Sector Erase Command
sequences must be issued for each sector. That is, only
a sector address can be specified for
each Sector Erase command.
Users must issue another Sector Erase command for the next
sector to be erased after the previous one is completed.
When the Embedded Erase algorithm is complete, the device returns to reading array data and
addresses are no longer latched. The system can determine the status of the erase operation by
This Data Sheet may be revised by subsequent versions
or modifications due to changes in technical specifications.
20
漏2005 Eon Silicon Solution, Inc., www.essi.com.tw
Rev. C, Issue Date: 2007/01/23

EN29LV640 PDF文件相关型号

EN29LV640H-90BCP,EN29LV640H-90BI

EN29LV640相关型号PDF文件下载

您可能感兴趣的PDF文件资料

热门IC型号推荐

©2024 维库电子市场网（www.dzsc.com）　备案号：浙B2-20050339-1 经营许可证：浙B2-20210386版权声明
买家服务热线：0571-85317607 | 买家服务部QQ： QQ:1609526468
卖家服务热线：0571-85317607 | 卖家服务部QQ： QQ:331652727

扫码下载APP，
一键连接广大的电子世界。

在线人工客服

买家服务：
卖家服务：

0571-85317607

客服在线时间周一至周五
9:00-17:30

关注官方微信号，
第一时间获取资讯。

建议反馈
返回顶部

建议反馈

联系人：

联系方式：

按住滑块，拖拽到最右边
>>
感谢您向阿库提出的宝贵意见，您的参与是维库提升服务的动力！意见一经采纳，将有感恩红包奉上哦！

PDF纠错X

投诉电话：0571-85317607 投诉QQ：

如选匿名将无法为您反馈投诉结果，建议实名投诉！