MC1489, MC1489A
APPLICATIONS INFORMATION
General Information
The Electronic Industries Association (EIA) has released
the EIA鈭?32D specification detailing the requirements for
the interface between data processing equipment and data
communications equipment. This standard specifies not
only the number and type of interface leads, but also the
voltage levels to be used. The MC1488 quad driver and its
companion circuit, the MC1489 quad receiver, provide a
complete interface system between DTL or TTL logic levels
and the EIA鈭?32D defined levels. The EIA鈭?32D
requirements as applied to receivers are discussed herein.
The required input impedance is defined as between
3000
W
and 7000
W
for input voltages between 3.0 and 25 V
in magnitude; and any voltage on the receiver input in an
open circuit condition must be less than 2.0 V in magnitude.
The MC1489 circuits meet these requirements with a
maximum open circuit voltage of one V
BE
.
The receiver shall detect a voltage between 鈭?3.0 and
鈭?5 V as a Logic 鈥?鈥?and inputs between 3.0 and 25 V as a
Logic 鈥?.鈥?On some interchange leads, an open circuit of
power 鈥淥FF鈥?condition (300
W
or more to ground) shall be
decoded as an 鈥淥FF鈥?condition or Logic 鈥?.鈥?For this
reason, the input hysteresis thresholds of the MC1489
circuits are all above ground. Thus an open or grounded
input will cause the same output as a negative or Logic 鈥?鈥?/div>
input.
Device Characteristics
The MC1489 interface receivers have internal feedback
from the second stage to the input stage providing input
hysteresis for noise rejection. The MC1489 input has typical
turn鈭抩n voltage of 1.25 V and turn鈭抩ff of 1.0 V for a typical
hysteresis of 250 mV. The MC1489A has typical turn鈭抩n of
1.95 V and turn鈭抩ff of 0.8 V for typically 1.15 V of
hysteresis.
Each receiver section has an external response control
node in addition to the input and output pins, thereby
allowing the designer to vary the input threshold voltage
levels. A resistor can be connected between this node and an
external power supply. Figures 4, 6 and 7 illustrate the input
threshold voltage shift possible through this technique.
This response node can also be used for the filtering of
high frequency, high energy noise pulses. Figures 10 and 11
show typical noise pulse rejection for external capacitors of
various sizes.
These two operations on the response node can be
combined or used individually for many combinations of
interfacing applications. The MC1489 circuits are
particularly useful for interfacing between MOS circuits and
MDTL/MTTL logic systems. In this application, the input
threshold voltages are adjusted (with the appropriate supply
and resistor values) to fall in the center of the MOS voltage
logic levels (see Figure 12).
The response node may also be used as the receiver input
as long as the designer realizes that he may not drive this
node with a low impedance source to a voltage greater than
one diode above ground or less than one diode below
ground. This feature is demonstrated in Figure 13 where two
receivers are slaved to the same line that must still meet the
EIA鈭?32D impedance requirement.
6
MC1489
5
E in , AMPLITUDE (V)
10 pF
4
3
2
1
10
100
1000
10,000
PW, INPUT PULSE WIDTH (ns)
E in , AMPLITUDE (V)
100 pF 300 pF
6
MC1489A
5
500 pF
12 pF
4
3
2
1
10
100
1000
10,000
PW, INPUT PULSE WIDTH (ns)
100 pF 300 pF
500 pF
Figure 10. Typical Turn On Threshold versus
Capacitance from Response Control Pin to GND
Figure 11. Typical Turn On Threshold versus
Capacitance from Response Control Pin to GND
http://onsemi.com
6
1
2
3
4
5
6
7
8
9
10
