您的位置：维库电子市场网 > Datasheet > BQ24703PWRG4

BQ24703PWRG4 Datasheet

  • BQ24703PWRG4

  • MULTICHEMISTRY BATTERY CHARGER CONTROLLER AND SYSTEM POWER S...

  • 518.72KB

  • 32页

  • TI

阅览下载 纠错 0

扫码查看芯片数据手册

上传产品规格书

PDF预览

bq24702, bq24703
SLUS553D 鈭?MAY 2003 鈭?REVISED JULY 2005
Smart Learn Cycles When Adapter Power Is Present
Smart learn cycles can be conducted when adapter power is present by asserting and maintaining the ACSEL
pin low. The adapter power can be reselected at the end of the learn cycle by a setting ACSEL to a logic high,
provided that adapter power is present. Battery charging is suspended while selected as the system power
source.
NOTE:
On the bq24703 the ac adapter is switched to the load when the battery voltage reaches
the battery depleted threshold; it can be used when the learn cycle does not require the battery
voltage to go below the battery depleted threshold. If the learn cycle algorithm requires the battery
voltage to go lower than the battery depleted voltage, the bq24702 should be used, as it does not
switch the ac adapter to load upon battery depleted detection.
System Break Before Make Function
When selecting the battery as the system primary power source, the adapter power select MOSFET turns off,
in a
break-before-make
fashion, before the battery select MOSFET turns on. To ensure that this happens under
all load conditions, the system voltage (load voltage) can be monitored through a resistor divider on the VS pin.
This function provides protection against switching over to battery power if the adapter selector switch were
shorted and adapter power present. Setting the VS resistive divider gain with the same gain selected for the
BATP resistive divider assures the battery switch is turned on only when the system voltage is equal or less than
the battery voltage. This function can be eliminated by grounding the VS pin.
The ACDET function senses the adapter voltage via a resistive divider (refer to application circuit).The divider
can be connected either to the anode of the input blocking diode (directly to the adapter supply) or to the cathode
of the input blocking diode (bq24702/3 VCC pin). When the divider is connected to the adapter supply, the
adapter power removal is immediately identified and the sleep mode is entered, disabling the
break-before-make function for system voltage (see section for system power switching) and coupling system
voltage to the battery line. In normal operation with a battery present, the battery low impedance prevents any
over-voltage conditions. However, if a pack is not present or the pack is open, the battery line voltage has a
transient equal to the adapter voltage. The bq24703 SRP/SRN pins are designed to withstand this over-voltage
condition, but avoid connection to the battery line of any external devices that are not rated to withstand the
adapter voltage.
Connecting the ACDET resistive divider input to the VCC node keeps the system break-before-make function
enabled until the voltage at pin VS is lower than the voltage at pin BATP. However, note that when using this
topology the VCC pin voltage can be held by capacitive loads at either the VCC or system (ac switch is on) nodes
when the ac adapter is removed. As the ACDET divider is connected to the VCC line there is a time delay from
ac adapter removal to ac adapter removal detection by the IC. This time is dependent on load conditions and
capacitive load values at VCC and system lines.
Battery Depletion Detection
The bq24702/bq24703 provides the host controller with a battery depletion discrete, the ALARM pin, to alert
the host when a depleted battery condition occurs. The battery depletion level is set by the voltage applied to
the BATDEP pin through a voltage divider network. The ALARM output asserts high and remains high as long
as the battery deplete condition exists, regardless of the power source selected.
For the bq24702, the host controller must take appropriate action during a battery deplete condition to select
the proper power source. The bq24702 remains on the selected power source. The bq24703, however,
automatically reverts over to adapter power, provided the adapter is present, during a deep discharge state. The
battery is considered as being in a deep discharge state when the battery voltage is less than (0.8
脳
depleted
level).
Feature sets for the bq24702 and bq24703 are detailed in Table 1.
24
www.ti.com

BQ24703PWRG4 产品属性

  • 2,000

  • 集成电路 (IC)

  • PMIC - 电池管理

  • -

  • 充电管理

  • 多化学

  • 4.5 V ~ 28 V

  • -40°C ~ 85°C

  • 表面贴装

  • 24-TSSOP（0.173"，4.40mm 宽）

  • 24-TSSOP

  • 带卷 (TR)

  • 296-18396-ND - EVALUATION MODULE FOR BQ24703

BQ24703PWRG4相关型号PDF文件下载

您可能感兴趣的PDF文件资料

热门IC型号推荐

©2024 维库电子市场网（www.dzsc.com）　备案号：浙B2-20050339-1 经营许可证：浙B2-20210386版权声明
买家服务热线：0571-85317607 | 买家服务部QQ： QQ:1609526468
卖家服务热线：0571-85317607 | 卖家服务部QQ： QQ:331652727

扫码下载APP，
一键连接广大的电子世界。

在线人工客服

买家服务：
卖家服务：

0571-85317607

客服在线时间周一至周五
9:00-17:30

关注官方微信号，
第一时间获取资讯。

建议反馈
返回顶部

建议反馈

联系人：

联系方式：

按住滑块，拖拽到最右边
>>
感谢您向阿库提出的宝贵意见，您的参与是维库提升服务的动力！意见一经采纳，将有感恩红包奉上哦！

PDF纠错X

投诉电话：0571-85317607 投诉QQ：

如选匿名将无法为您反馈投诉结果，建议实名投诉！