TIMESTREAM
TM
PRODUCT FAMILY
VSC9186
VSC9186 Killington - Quad STS-48/STM-16 and STS-192/STM-64 Line Interface
S P E C I F I C AT I O N S :
2.5V I/O and 1.8V Core Power Supplies
0.18碌 CMOS Technology
720-pin CCGA /1.0mm Column Pitch
10W Maximum Power Consumption
SPLITTER/COMBINER MODE (DWDM):
Four independently-timed 2.5Gb/s SONET/SDH signals are received,
terminated, and monitored at the line level. They are pointer processed to
the local time domain, passed through an STS-1 level crossconnect, and are
multiplexed to a STS-192/STM-64 signal. A STS-192/STM-64 is received in
the opposite direction and pointer processed to a local clock. The signal
is crossconnected at the STS-1 level and then demultiplexed to four
STS-48/STM-16 signals. Full section and line termination are performed at
all five SONET Tx and Rx interfaces. Overhead transparency is supported
through an external interface for maximum customer flexibility.
Two Killington devices may to be used in an East/West ring configuration
forming a logical 40Gb/s crossconnect. Two bidirectional interfaces allow
loopback of all four STS-48/STM-16 and the STS-192/ STM-64 interfaces
simultaneously.
F E AT U R E S :
Bidirectional Quad STS-48/STM-16 or STS-192/ STM-64
Section and Line Termination Device with Pointer Processing
and Time Slot Interchange
Accommodates a +/- 300ppm Difference Between Incoming
and Local System Clock and Performs Pointer Processing on
Quad Independent STS-48/ STM-16 or a Single STS-192/STM-64
Pointer Processing of all Concatenation Levels Including
STS-192c, STS-48c, STS-12c, STS-3c, and STS-1
Three ports featuring 16 Serial 622Mb/s Timestream Backplane
Interfaces with Integrated CDR to Other Line Interfaces or
Switch ICs
Section/Line OH Drop/Insertion with External Interfaces on
All Channels
Supports Section/Line Overhead Transparency
Protection Interface Allows Full STS-1/STM-0 Hairpinning and
Drop/Continue on Both Tributary and Ring Traffic
Two Integrated Bidirectional 768 x 288 STS-1 Level Crossconnects
Embedded Hardware UPSR
Compliant with SONET and SDH Requirements as Stated in
ANSI T1.105, Bellcore GR-253-CORE and ITU-T G.707
Provides JTAG TAP Controller Conforming to the IEEE 1149.1
Standard
Bidirectional Path Monitoring
A D D / D R O P M U LT I P L E X I N G ( A D M ) M O D E :
Four independently-timed 2.5Gb/s signals or a single 10Gb/s SONET/SDH
signal are received, terminated, and monitored at the line level. The incoming
192 STS-1 signals are sent through a 768 x 288 STS-1 TSI switch that allows
ring loopback or hairpinning of tributaries from either the line interface or
the backplane interface. B1 parity is supported on both interfaces for backplane
integrity monitoring.
The backplane receive circuitry has built-in data recovery and realignment of
+/- 100 ns on all 16 working and protection LVDS inputs. These signals are
then crossconnected again at the STS-1 level through a 768 x 288 TSI and
transmitted to either four STS-48/STM-16 or one STS-192/STM-64 interface.
PB-VSC9186-001
1
2
