您的位置：维库电子市场网 > Datasheet > ST7232AK1B1

ST7232AK1B1 Datasheet

  • ST7232AK1B1

  • 8-BIT MCU WITH 8K FLASH/ROM, ADC, 4 TIMERS, SPI, SCI INTERFA...

  • 1290.53KB

  • 154页

  • STMICROELECTRONICS   STMICROELECTRONICS

阅览下载 纠错 0

扫码查看芯片数据手册

上传产品规格书

PDF预览

ST7232A
16-BIT TIMER
(Cont鈥檇)
10.3.3.5 One Pulse Mode
One Pulse mode enables the generation of a
pulse when an external event occurs. This mode is
selected via the OPM bit in the CR2 register.
The one pulse mode uses the Input Capture1
function and the Output Compare1 function.
Procedure:
To use one pulse mode:
1. Load the OC1R register with the value corre-
sponding to the length of the pulse (see the for-
mula in the opposite column).
2. Select the following in the CR1 register:
鈥?Using the OLVL1 bit, select the level to be ap-
plied to the OCMP1 pin after the pulse.
鈥?Using the OLVL2 bit, select the level to be ap-
plied to the OCMP1 pin during the pulse.
鈥?Select the edge of the active transition on the
ICAP1 pin with the IEDG1 bit (the ICAP1 pin
must be configured as floating input).
3. Select the following in the CR2 register:
鈥?Set the OC1E bit, the OCMP1 pin is then ded-
icated to the Output Compare 1 function.
鈥?Set the OPM bit.
鈥?Select the timer clock CC[1:0] (see
Table 16
Clock Control Bits).
One pulse mode cycle
When
event occurs
on ICAP1
ICR1 = Counter
OCMP1 = OLVL2
Counter is reset
to FFFCh
ICF1 bit is set
When
Counter
= OC1R
Clearing the Input Capture interrupt request (i.e.
clearing the ICFi bit) is done in two steps:
1. Reading the SR register while the ICFi bit is set.
2. An access (read or write) to the ICiLR register.
The OC1R register value required for a specific
timing application can be calculated using the fol-
lowing formula:
t
*
f
CPU
-5
OCiR Value =
PRESC
Where:
t
= Pulse period (in seconds)
f
CPU
= CPU clock frequency (in hertz)
PRESC
= Timer prescaler factor (2, 4 or 8 depend-
ing on the CC[1:0] bits, see
Table 16
Clock Control Bits)
If the timer clock is an external clock the formula is:
OCiR =
t
*
f
EXT
-5
Where:
t
= Pulse period (in seconds)
= External timer clock frequency (in hertz)
f
EXT
When the value of the counter is equal to the value
of the contents of the OC1R register, the OLVL1
bit is output on the OCMP1 pin, (See
Figure 41).
Notes:
1. The OCF1 bit cannot be set by hardware in one
pulse mode but the OCF2 bit can generate an
Output Compare interrupt.
2. When the Pulse Width Modulation (PWM) and
One Pulse Mode (OPM) bits are both set, the
PWM mode is the only active one.
3. If OLVL1=OLVL2 a continuous signal will be
seen on the OCMP1 pin.
4. The ICAP1 pin can not be used to perform input
capture. The ICAP2 pin can be used to perform
input capture (ICF2 can be set and IC2R can be
loaded) but the user must take care that the
counter is reset each time a valid edge occurs
on the ICAP1 pin and ICF1 can also generates
interrupt if ICIE is set.
5. When one pulse mode is used OC1R is dedi-
cated to this mode. Nevertheless OC2R and
OCF2 can be used to indicate a period of time
has been elapsed but cannot generate an out-
put waveform because the level OLVL2 is dedi-
cated to the one pulse mode.
6. In Flash devices, Timer A OCF2 bit is forced by
hardware to 0.
OCMP1 = OLVL1
Then, on a valid event on the ICAP1 pin, the coun-
ter is initialized to FFFCh and OLVL2 bit is loaded
on the OCMP1 pin, the ICF1 bit is set and the val-
ue FFFDh is loaded in the IC1R register.
Because the ICF1 bit is set when an active edge
occurs, an interrupt can be generated if the ICIE
bit is set.
63/154
1

ST7232AK1B1相关型号PDF文件下载

您可能感兴趣的PDF文件资料

热门IC型号推荐

©2024 维库电子市场网（www.dzsc.com）　备案号：浙B2-20050339-1 经营许可证：浙B2-20210386版权声明
买家服务热线：0571-85317607 | 买家服务部QQ： QQ:1609526468
卖家服务热线：0571-85317607 | 卖家服务部QQ： QQ:331652727

扫码下载APP，
一键连接广大的电子世界。

在线人工客服

买家服务：
卖家服务：

0571-85317607

客服在线时间周一至周五
9:00-17:30

关注官方微信号，
第一时间获取资讯。

建议反馈
返回顶部

建议反馈

联系人：

联系方式：

按住滑块，拖拽到最右边
>>
感谢您向阿库提出的宝贵意见，您的参与是维库提升服务的动力！意见一经采纳，将有感恩红包奉上哦！

PDF纠错X

投诉电话：0571-85317607 投诉QQ：

如选匿名将无法为您反馈投诉结果，建议实名投诉！