Absolute Maximum Ratings*
Operating Temperature .................................. -55掳C to +125掳C
*NOTICE:
Stresses beyond those listed under 鈥淎bsolute
Maximum Ratings鈥?may cause permanent dam-
age to the device. This is a stress rating only and
functional operation of the device at these or any
other conditions beyond those indicated in the
operational sections of this specification is not
implied. Exposure to absolute maximum rating
conditions for extended periods may affect device
reliability.
Storage Temperature ..................................... -65掳C to +150掳C
Voltage on Any Pin
with Respect to Ground .....................................-1.0V to +7.0V
Maximum Operating Voltage............................................. 6.6V
DC Output Current...................................................... 15.0 mA
DC Characteristics
The values shown in this table are valid for T
A
= -40掳C to 85掳C and V
CC
= 2.7V to 6.0V, unless otherwise noted.
Symbol
V
IL
V
IL1
V
IH
V
IH1
V
OL
V
OL1
V
OH
Parameter
Input Low Voltage
Input Low Voltage (EA)
Input High Voltage
Input High Voltage
Output Low Voltage
(1)
(Ports 1,2,3)
Output Low Voltage
(1)
(Port 0, ALE, PSEN)
Output High Voltage
(Ports 1,2,3, ALE, PSEN)
(Except XTAL1, RST)
(XTAL1, RST)
I
OL
= 1.6 mA
I
OL
= 3.2 mA
I
OH
= -60
碌A,
V
CC
= 5V
卤
10%
I
OH
= -25
碌A
I
OH
= -10
碌A
V
OH1
Output High Voltage
(Port 0 in External Bus Mode)
I
OH
= -800
碌A,
V
CC
= 5V
卤
10%
I
OH
= -300
碌A
I
OH
= -80
碌A
I
IL
I
TL
I
LI
RRST
C
IO
I
CC
Logical 0 Input Current (Ports 1,2,3)
Logical 1 to 0 Transition Current
(Ports 1,2,3)
Input Leakage Current (Port 0, EA)
Reset Pulldown Resistor
Pin Capacitance
Power Supply Current
Test Freq. = 1 MHz, T
A
= 25掳C
Active Mode, 12 MHz
Idle Mode, 12 MHz
Power Down Mode
(2)
Notes:
V
CC
= 6V
V
IN
= 0.45V
V
IN
= 2V
0.45 < V
IN
< V
CC
50
2.4
0.75 V
CC
0.9 V
CC
2.4
0.75 V
CC
0.9 V
CC
-50
-650
卤10
300
10
25
6.5
100
Condition
(Except EA)
Min
-0.5
-0.5
0.2 V
CC
+ 0.9
0.7 V
CC
Max
0.2 V
CC
- 0.1
0.2 V
CC
- 0.3
V
CC
+ 0.5
V
CC
+ 0.5
0.45
0.45
Units
V
V
V
V
V
V
V
V
V
V
V
V
碌A
碌A
碌A
K鈩?/div>
pF
mA
mA
碌A
V
CC
= 3V
1. Under steady state (non-transient) condition, I
OL
must be externally limited as follows:
Maximum I
OL
per port pin: 10 mA
Maximum I
OL
per 8-bit port: Port 0: 26 mA
Ports 1, 2, 3: 15 mA
Maximum total I
OL
or all output pins: 71 mA
40
碌A
If I
OL
exceeds the test condition, V
OL
may exceed the
related specification. Pins are not guaranteed to sink
current greater than the listed test conditions.
2. Minimum V
CC
for Power Down is 2V.
4-98
AT89LV52
prev
next