您的位置：维库电子市场网 > Datasheet > VIPER20A-E

VIPER20A-E Datasheet

  • VIPER20A-E

  • VIPer20A-E Series 15 V 16 mA SMPS primary I.C. - PENTAWATT H...

  • 572.80KB

  • 34页

  • STMicroelectronics

阅览下载 纠错 0

扫码查看芯片数据手册

上传产品规格书

PDF预览

Operation description
VIPer20A-E
As soon as the power goes below this limit, the auxiliary secondary voltage starts to increase
above the 13V regulation level, forcing the output voltage of the transconductance amplifier to
low state (V
COMP
< V
COMPth
). This situation leads to the shutdown mode where the power
switch is maintained in the Off state, resulting in missing cycles and zero duty cycle. As soon as
V
DD
gets back to the regulation level and the V
COMPth
threshold is reached, the device operates
again. The above cycle repeats indefinitely, providing a burst mode of which the effective duty
cycle is much lower than the minimum one when in normal operation. The equivalent switching
frequency is also lower than the normal one, leading to a reduced consumption on the input
main supply lines. This mode of operation allows the VIPer20A-E to meet the new German
"Blue Angel" Norm with less than 1W total power consumption for the system when working in
stand-by mode. The output voltage remains regulated around the normal level, with a low
frequency ripple corresponding to the burst mode. The amplitude of this ripple is low, because
of the output capacitors and low output current drawn in such conditions.The normal operation
resumes automatically when the power gets back to higher levels than P
STBY
.
5.3
High voltage start-up current suorce
An integrated high voltage current source provides a bias current from the DRAIN pin during
the start-up phase. This current is partially absorbed by internal control circuits which are
placed into a standby mode with reduced consumption and also provided to the external
capacitor connected to the V
DD
pin. As soon as the voltage on this pin reaches the high voltage
threshold V
DDon
of the UVLO logic, the device becomes active mode and starts switching. The
start-up current generator is switched off, and the converter should normally provide the
needed current on the V
DD
pin through the auxiliary winding of the transformer, as shown on
(see Figure 11).
In case there are abnormal conditions where the auxiliary winding is unable to provide the low
voltage supply current to the V
DD
pin (i.e. short circuit on the output of the converter), the
external capacitor discharges to the low threshold voltage V
DDoff
of the UVLO logic, and the
device goes back to the inactive state where the internal circuits are in standby mode and the
start-up current source is activated. The converter enters a endless start-up cycle, with a start-
up duty cycle defined by the ratio of charging current towards discharging when the VIPer20-E
tries to start. This ratio is fixed by design to 2A to 15A, which gives a 12% start-up duty cycle
while the power dissipation at start-up is approximately 0.6W, for a 230Vrms input voltage.
This low value start-up duty cycle prevents the application of stress to the output rectifiers as
well as the transformer when a short circuit occurs.
The external capacitor C
VDD
on the V
DD
pin must be sized according to the time needed by the
converter to start up, when the device starts switching. This time t
SS
depends on many
parameters, among which transformer design, output capacitors, soft start feature, and
compensation network implemented on the COMP pin. The following formula can be used for
defining the minimum capacitor needed:
I
t
DD SS
--------------------
C
VDD
>
V
DDhyst
where:
I
DD
is the consumption current on the V
DD
pin when switching. Refer to specified I
DD1
and I
DD
2
values.
t
SS
is the start up time of the converter when the device begins to switch. Worst case is
generally at full load.
V
DDhyst
is the voltage hysteresis of the UVLO logic (refer to the minimum specified value).
12/34

VIPER20A-E 产品属性

  • VIPER20A-E View All Specifications

  • VIPerPlus

  • 1,000

  • 集成电路 (IC)

  • PMIC - AC-DC 转换器，离线开关

  • VIPER™

  • 隔离

  • 90kHz ~ 200kHz

  • 8 V ~ 15 V

  • 700V

  • 57W

  • 25°C ~ 125°C

  • Pentawatt-5 HV（弯曲和错列引线）

  • 5-PENTAWATT

  • 管件

  • 497-6796-5VIPER20A-E-ND

VIPER20A-E相关型号PDF文件下载

您可能感兴趣的PDF文件资料

热门IC型号推荐

©2024 维库电子市场网（www.dzsc.com）　备案号：浙B2-20050339-1 经营许可证：浙B2-20210386版权声明
买家服务热线：0571-85317607 | 买家服务部QQ： QQ:1609526468
卖家服务热线：0571-85317607 | 卖家服务部QQ： QQ:331652727

扫码下载APP，
一键连接广大的电子世界。

在线人工客服

买家服务：
卖家服务：

0571-85317607

客服在线时间周一至周五
9:00-17:30

关注官方微信号，
第一时间获取资讯。

建议反馈
返回顶部

建议反馈

联系人：

联系方式：

按住滑块，拖拽到最右边
>>
感谢您向阿库提出的宝贵意见，您的参与是维库提升服务的动力！意见一经采纳，将有感恩红包奉上哦！

PDF纠错X

投诉电话：0571-85317607 投诉QQ：

如选匿名将无法为您反馈投诉结果，建议实名投诉！