您的位置：维库电子市场网 > Datasheet > DS2505
DS2505数据手册封面

DS2505 Datasheet

  • DS2505

  • 16-kbit Add-Only Memory

  • 499.10KB

  • Dallas

阅览下载 纠错 0

扫码查看芯片数据手册

上传产品规格书

PDF预览

DS2505
Match ROM [55H]
The Match ROM command, followed by a 64-bit ROM sequence, allows the bus master to address a
specific DS2505 on a multidrop bus. Only the DS2505 that exactly matches the 64-bit ROM sequence
will respond to the subsequent memory function command. All slaves that do not match the 64-bit ROM
sequence will wait for a reset pulse. This command can be used with a single or multiple devices on the
bus.
Skip ROM [CCH]
This command can save time in a single-drop bus system by allowing the bus master to access the
memory functions without providing the 64-bit ROM code. If more than one slave is present on the bus
and a read command is issued following the Skip ROM command, data collision will occur on the bus as
multiple slaves transmit simultaneously (open drain pulldowns will produce a wired-AND result).
Search ROM [F0H]
When a system is initially brought up, the bus master might not know the number of devices on the
1-Wire bus or their 64-bit ROM codes. The Search ROM command allows the bus master to use a
process of elimination to identify the 64-bit ROM codes of all slave devices on the bus. The ROM search
process is the repetition of a simple, three-step routine: read a bit, read the complement of the bit, then
write the desired value of that bit. The bus master performs this simple, three-step routine on each bit of
the ROM. After one complete pass, the bus master knows the contents of the ROM in one device. The
remaining number of devices and their ROM codes may be identified by additional passes. See Chapter 5
of the Book of DS19xx iButton Standards for a comprehensive discussion of a ROM search, including an
actual example.
1-Wire Signaling
The DS2505 requires strict protocols to ensure data integrity. The protocol consists of five types of
signaling on one line: Reset Sequence with Reset Pulse and Presence Pulse, Write 0, Write 1, Read Data
and Program Pulse. All these signals except presence pulse are initiated by the bus master. The
initialization sequence required to begin any communication with the DS2505 is shown in Figure 9. A
reset pulse followed by a presence pulse indicates the DS2505 is ready to accept a ROM command. The
bus master transmits (TX) a reset pulse (t
RSTL
, minimum 480 碌s). The bus master then releases the line
and goes into receive mode (RX). The 1-Wire bus is pulled to a high state via the pullup resistor. After
detecting the rising edge on the data pin, the DS2505 waits (t
PDH
, 15-60 碌s) and then transmits the
presence pulse (t
PDL
, 60-240 碌s).
Read/Write Time Slots
The definitions of write and read time slots are illustrated in Figure 10. All time slots are initiated by the
master driving the data line low. The falling edge of the data line synchronizes the DS2505 to the master
by triggering a delay circuit in the DS2505. During write time slots, the delay circuit determines when
the DS2505 will sample the data line. For a read data time slot, if a 鈥?鈥?is to be transmitted, the delay
circuit determines how long the DS2505 will hold the data line low overriding the 1 generated by the
master. If the data bit is a 鈥?鈥? the device will leave the read data time slot unchanged.
PROGRAM PULSE
To copy data from the 8-bit scratchpad to the EPROM Data or Status Memory, a program pulse of
12 volts is applied to the data line after the bus master has confirmed that the CRC for the current byte is
correct. During programming, the bus master controls the transition from a state where the data line is
idling high via the pullup resistor to a state where the data line is actively driven to a programming
voltage of 12 volts providing a minimum of 10 mA of current to the DS2505. This programming voltage
18 of 24

DS2505 产品属性

  • 1

  • 集成电路 (IC)

  • 存储器

  • -

  • EPROMs

  • EPROM OTP

  • 16K（16K x 1）

  • -

  • 1 线 串行

  • -

  • -40°C ~ 85°C

  • TO-226-3、TO-92-3 标准主体

  • TO-92-3

  • 散装

DS2505相关型号PDF文件下载

您可能感兴趣的PDF文件资料

热门IC型号推荐

©2024 维库电子市场网（www.dzsc.com）　备案号：浙B2-20050339-1 经营许可证：浙B2-20210386版权声明
买家服务热线：0571-85317607 | 买家服务部QQ： QQ:1609526468
卖家服务热线：0571-85317607 | 卖家服务部QQ： QQ:331652727

扫码下载APP，
一键连接广大的电子世界。

在线人工客服

买家服务：
卖家服务：

0571-85317607

客服在线时间周一至周五
9:00-17:30

关注官方微信号，
第一时间获取资讯。

建议反馈
返回顶部

建议反馈

联系人：

联系方式：

按住滑块，拖拽到最右边
>>
感谢您向阿库提出的宝贵意见，您的参与是维库提升服务的动力！意见一经采纳，将有感恩红包奉上哦！

PDF纠错X

投诉电话：0571-85317607 投诉QQ：

如选匿名将无法为您反馈投诉结果，建议实名投诉！